Common sense of entering, exiting and taking elevators

Core tips: 1. When entering and exiting the elevator floor and the car door is opened, passengers should get off first and then get on, and do not push each other. When the landing door is fully opened, before entering the car, check the floor and floor of the elevator car.

1. In and out of the elevator

When the elevator floor and car doors are opened, passengers should get off first and then get on, and do not push each other. When the landing door is fully opened, before entering the car, make sure that the floor of the elevator car and the floor of the floor are on the same plane, so as to avoid tripping due to inaccurate elevator leveling. When reaching the destination floor, after the car stops and the door is fully opened, make sure that the floor of the car and the floor are on the same plane, and then get out of the car.

When entering or leaving the car, you also need to pay attention to the following matters: It is forbidden to run into or out of the car when the elevator closes the door; , so as not to pinch hands; pay attention to prevent crutches and stilettos from getting stuck in the groove of the entrance sill or the gap between the two to avoid being clamped; when the elevator is overloaded, there will be a sound and light alarm and the elevator cannot close and start, and passengers who enter later You should exit the car actively, wait for the next elevator, and press the call button after the elevator door is completely closed and starts to start. A fully loaded elevator will not answer other floor calls until some passengers leave the elevator. This is not a malfunction, but a design to ensure elevator safety and improve operating efficiency.

2. Open and close the elevator door

Most of the elevators in daily use are in the automatic state. The elevator floor and car door will automatically close after the time set by the control system. You can also press the door close button ">|<" on the car control panel to make the floor and car door close immediately. , to achieve early closing. The elevator starts running after the floor and car doors are closed. When the elevator reaches the destination floor, the elevator floor and car doors will automatically open.

If you need to delay closing the elevator floor and car door, you can press and hold the door open button "<|>" on the car control panel. It is forbidden to use boxes and other objects or the body to block the closing of the floor and the car door, especially do not straddle the standing blocking floor and the car door between the landing and the car, so as to avoid personal injury.

When the elevator floor and the car door are closing, it is very dangerous to directly block the closing door with hands or feet. If it is necessary to prevent the elevator from closing the door, passengers at the landing can press the outbound call button in the direction of the elevator in the waiting hall; when passengers are in the car, they can press the door opening button "<|>", and the elevator floor and car door will be opened. reopen the door. However, the door is directly blocked by hands, feet, etc. Although the floor and car doors are usually automatically reopened under the action of the safety protection device (light curtain or safety touch panel), when the door system detects the blind spot or the door system fails, the elevator will not open again. May cause harm to the human body.

3. Floor selection in the car

Inside the car, there is a car control panel indicating each floor. Passengers who enter the car press the button of the destination floor, the selected button indicator light will light up, and the button light will light up to indicate that the selected floor has been registered by the elevator control system. If the button of the destination floor that the passenger wants to go to is already lit, do not select it again, and do not select the button of the floor that cannot be pressed. For elevators with light-load anti-disturb function, when there are few passengers in the elevator car, the load in the car is lower than the set value of the elevator control system, and the destination floors selected by passengers are many (the value can be adjusted in the control system) , the elevator control system will eliminate all floor selection instructions, and passengers need to press the button of the destination floor again, which is not an elevator fault.

In addition, some elevators have the function of canceling the wrong command. If the floor is selected in the car and the wrong floor is selected, by continuously pressing the button for this floor several times (some elevators are long-pressed), the button indicator of the floor will go out. Indicates that the layer selection is canceled.

4. Take the elevator

After entering the car, passengers should stand inside the car, do not hold hands or lean against the safety touch panel (or light curtain), so as not to affect the closing of the floor and car door, and do not get too close to the car door, especially if the passengers are wearing loose clothes, When dragging clothing (such as long skirts, dresses, etc.), pay attention to avoid the clothing being caught by the floor and the car door, which may cause personal injury.

When the elevator car arrives at the station, the elevator floor and car doors are automatically opened, the floor number is displayed on the car control panel, the corresponding floor button indicator light will be off, and the barrier-free elevator will also have a sound prompt to inform passengers of the parking position of the car.